NestAssociate is reader-supported. When you buy via the links on our site, we may earn an affiliate commission at no cost to you.

How To Increase Water Pressure In Your Shower

How To Increase Water Pressure In Your Shower: 11 Best Tips

Do you have issues with how to increase water pressure in your shower? Don’t worry. Check out this guide to learn what’s causing it and how to solve them. Low pressure may occur as a result of leakages or blockages of your plumbing system in your premises.

Therefore, to prevent these blockages, it is vital to ensure that your plumbing system is installed well with expert plumbers. Additionally, areas with old water pipes may cause water pressure to decrease tremendously, putting a significant impact on your shower.

Among many other causes, let’s now turn our eyes on the steps involved to increase the water pressure in your shower.

How To Increase Water Pressure In Your Shower: Top 11 Tips

 1. Clean the showerhead

Showerheads usually develop small sediments and particles of mineral deposits that make the block. Therefore, this slows down the rate of flow of water even at high pressure. To prevent this from happening, unscrew the head of the shower and remove any sediment from inside by cleaning.

For the perfect cleaning of the shower, there are crucial steps involved when cleaning the showerhead, as explained below.

Rubbing the nozzle

Rubbing the nozzle

Most of the showerheads consist of flexible nozzles that enable the users to clean easily. Therefore, cleaning involves rubbing of fingers on the nozzle to clean the nozzles clogged.

Soaking in vinegar

It involves filling a plastic bag having vinegar while wrapping it around the showerhead with a tape or rubber band and allowing it to stay for a couple of times. Next, you can remove the plastic bag containing vinegar as you turn the water on for some minutes to remove the vinegar entirely from the head.

In case you clear the showerhead, it is good to soak it again into the container filled with vinegar and allow it for some time.

Cleaning the filter screen

Using the showerhead manual, one can clean the screen easily following the steps. The screen is on the showerhead, where the pipe of the shower connects. Therefore, it is good to remove the head first to see the filter screen.

However, for successful removal of the screen, you can comfortably use the pliers or tweezers to extract it from the pivot. Once you have removed it, you can run water to the screen while using a brush to clean it gently.

2. Check for the Flow Restrictor

Check for the Flow Restrictor

Flow restrictors play a vital role in reducing the water bills of the customers and protecting the environment. However, if you are staying in a home with low water pressure, then the flow restrictor will help to reduce a little flow to the worst dribble.

But how? Simple. First, begin by removing the flow restrictor following the steps indicated on the manual guide that accompanies the showerhead. After the successful removal of the restrictor, return the showerhead and recheck to see whether the flow is okay.

3. Check for kinks

It is also good to consider checking the kinks in the water line or in the hose to fix it quickly. Therefore, in case the shower consists of a flexible apart from the ordinal pipes, then ensure that there are no further kinks that may prevent water from flowing.

However, if the shower has a handheld head, it is crucial to ensure that the hose remains twisted.

4. Ensure that the valve is open

Checking whether the main shut-off valve is open is crucial, especially if you have relocated to a new house. The workers may shut off the valve and critically forget to open it immediately after they are done with the job.

Usually, the valve is at the central system or the basement entering your premises. It has a red lever for easy identification. There are two main types of pipes located in the showerhead.

Main valve

The primary water source to your house is always found near your water meter. When checking, you will see two valves, and you can turn them counterclockwise for fully opening.

Shower valve

Usually, the shower valve is in the basement of your home, behind the panel shower, or at the crawl space. To open it up, you can turn it counterclockwise.

5. Identify for any leakages

Identify for any leakages

The presence of the leaking pipes dramatically reduces the rate and amount of water reaching your shower. Consequently, the leaking of water causes tremendous damage to your home. Therefore, it is good to check for any leakages available and take quick action of repairing them.

Most of the leakages may occur from either the main basement or on the pipes. Therefore you must survey the entire system to ensure that all the loops are well fixed.

6. Open the water heater shut off valve

Generally, if there is low pressure when using hot water and high pressure when using cold water, then the problem is likely to emanate from the water heater. Therefore, ensure that the shut-off valve is open when closed.

How To Increase Water Pressure In Your Shower: Tips 7-11

7. Flush the water heater

When the water tank has blockage issues due to the sediments, it brings about water heater-related problems. Whenever this happens, you can drain the water heater while flushing out all the fixed lines to remove all the sediment and debris from the pipe.

8. Buy a low-pressure shower head

Specially designed low-pressure showerheads are essential in increasing the flow of water, especially when the problem has no relation to plumbing issues. They help in producing a powerful water jet for the plumbing of water than other showers.

However, the low-pressure showerhead may not be appropriate but is the best solution, especially when you experience low pressure on your shower.

9. Install a shower pump or similar

how to increase water pressure in your shower

Installation of a power pump helps to boost the pressure of water. However, it may appear to be relatively expensive, but more affordable. The installation requires an expert for it to last for long. Equally, it is good to ask the plumber for an alternative for such a situation.

10. Take a shower during off-peak hours

Taking a shower during off-peak hours is crucial, especially when you are not willing to spend money at the pump. Therefore, take your shower when many people are not using it. At this time, more water runs with high pressure when the demand is low.

11. Turn off other appliances

When taking a shower, it is good to turn off other electrical appliances to reduce the demand for electricity. Additionally, taking your shower first, followed by a dishwasher, is necessary to reduce the demand for the supply of water.

Read Also


Increasing water pressure in your shower is one of the best things in your home for better and quick bathing. However, in most cases, showerheads are responsible for the slow and low running of water. Therefore, regular cleaning helps to normalize the flow of water.

Alternatively, when you experience low pressure from your shower, probably there might be a plumbing issue, so you need to hire for a professional and expert plumber to check for any problem. Therefore, for the proper workability of your shower, there must be regular checking.

Leave a Comment

Your email address will not be published.

You can easily find the best products according to consumer reviews and ratings. Our AI technology finds the best product and describes it according to customer reviews and ratings. Not all information on this blog is 100 percent accurate.