NestAssociate is reader-supported. When you buy via the links on our site, we may earn an affiliate commission at no cost to you.

How To Install A Moen 1225 Cartridge

If you’re like most people, you probably don’t think about your sink very much. But when something goes wrong, it quickly becomes the center of your attention. A broken faucet can be a major annoyance, and fixing it is usually a pretty simple matter.

In this article, we’ll show you how to replace a Moen 1225 cartridge. Moen faucets are known for their quality, so it’s no surprise that the 1225 is one of the most popular models. If you have this faucet, chances are it’s been giving you years of trouble-free service.

But eventually, even the best faucets will need some attention.

  • Turn off the water to your sink
  • Remove the handle from your Moen 1225 cartridge faucet
  • Unscrew the retaining clip from the top of the cartridge
  • Pull the cartridge out of the faucet
  • Inspect the O-rings on the bottom of the cartridge and replace them if necessary
  • Insert the new cartridge into the faucet
  • Screw the retaining clip back into place
  • Put the handle back on the faucet
  • Turn the water back on and check for leaks

How to install Moen 1225 & 1225b Shower Cartridge. Similar to 1222

Moen 1225 cartridge removal tool

If you’re like most people, you probably don’t think about your Moen 1225 cartridge removal tool until you need it. And when you do need it, you probably don’t have a clue where to find it. But don’t worry, we’re here to help.

The Moen 1225 cartridge removal tool is a small, plastic tool that is used to remove the Moen 1225 cartridge from the faucet. The tool is inserted into the top of the cartridge and turned counterclockwise to loosen and remove the cartridge. The Moen 1225 cartridge removal tool is a essential tool for any homeowner or plumber.

If you need to replace your Moen 1225 cartridge, or if you’re having any other issues with your Moen faucet, this tool will come in handy. So where can you find the Moen 1225 cartridge removal tool? You can find it at most hardware stores, or you can order it online.

We hope this article was helpful. If you have any further questions, feel free to contact us or leave a comment below.

how to install a moen 1225 cartridge

Credit: terrylove.com

Which way does a Moen cartridge go in?

Moen is a well-known manufacturer of kitchen and bathroom fixtures. One of their most popular products is the Moen faucet. The Moen faucet is a cartridge-type faucet, meaning that a replaceable cartridge is what controls the flow of water through the faucet.

If you need to replace the cartridge in your Moen faucet, you may be wondering which way it goes in. The answer is that it depends on the model of Moen faucet you have. Some Moen faucets have a cartridge that can be installed in either direction.

Others have a cartridge that can only be installed in one direction. If your Moen faucet has a cartridge that can be installed in either direction, it is important to install it so that the water flow arrow on the cartridge is pointing in the right direction. This will ensure that water flows through the faucet in the correct direction.

If your Moen faucet has a cartridge that can only be installed in one direction, it is important to follow the installation instructions that came with the faucet. These instructions will indicate which way the cartridge needs to be installed. Installing a Moen faucet cartridge is a relatively easy task that can be completed in a few minutes.

Once you know which way the cartridge needs to go in, the rest is simply a matter of following the instructions.

What is the difference between Moen 1225 and 1225b cartridge?

The Moen 1225 and 1225b cartridges are very similar, but there are a few key differences. The 1225b cartridge is designed for use with 1 or 2 handle faucets, while the 1225 is designed for 3 handle faucets. The 1225b also has a slightly different pressure balance valve than the 1225.

Finally, the 1225b has a built in check valve, while the 1225 does not.

How do I change the cartridge in my Moen single lever kitchen faucet?

If your Moen single lever kitchen faucet is leaking, or you simply want to replace the cartridge, follow these steps. You will need a Phillips screwdriver, a towel and a new cartridge (Moen 1225). 1. Turn off the water to your faucet.

There should be a shut-off valve under your sink. 2. Unscrew the handle of your faucet. 3. Use the towel to remove the old cartridge.

4. Insert the new cartridge into the faucet. 5. Screw the handle back on. 6. Turn the water back on and check for leaks.

How do you install a Moen cartridge clip?

If you’re looking to install a Moen cartridge clip, you’ll first need to gather the necessary tools. You’ll need a Phillips head screwdriver, a flat head screwdriver, a crescent wrench, and a utility knife. You’ll also need a Moen replacement cartridge, which can be found at most hardware stores.

Once you have your tools and replacement cartridge, begin by shutting off the water supply to your Moen faucet. Then, use the Phillips head screwdriver to remove the screw from the handle of the faucet. Next, use the flat head screwdriver to pry off the index button and cap, which are located under the screw.

With the index button and cap removed, you should now be able to see the retaining clip that holds the cartridge in place. Use the utility knife to carefully remove the retaining clip. Be careful not to damage the cartridge as you remove it.

Once the old cartridge is removed, take your new replacement cartridge and insert it into the faucet. Make sure that the O-rings are properly in place. Then, use the retaining clip to secure the new cartridge in place.

Finally, reassemble the index button and cap, and screw the handle back into place. Turn on the water supply and test your faucet to make sure it’s working properly. If everything is working as it should, you’ve successfully installed your new Moen cartridge clip!

Conclusion

If your Moen faucet is leaking or you’re simply interested in replacing the 1225 cartridge, follow these steps. First, remove the handle by unscrewing the retaining screw with a hex wrench or Allen key. With the handle removed, use a crescent wrench to unscrew the collar and pull out the old cartridge.

Inspect the O-rings and seats for wear and replace them if necessary. Lubricate the new O-rings with plumber’s grease and insert the cartridge, making sure it’s seated properly. Screw on the collar and reattach the handle.

Test your faucet to make sure it’s working properly.

You can easily find the best products according to consumer reviews and ratings. Our AI technology finds the best product and describes it according to customer reviews. Not all information on this blog is 100 percent accurate.