NestAssociate is reader-supported. When you buy via the links on our site, we may earn an affiliate commission at no cost to you.

How To Remove A Shower Handle

There are a few different ways that you can remove a shower handle, depending on the type of handle that you have. If you have a screw-on type of handle, then you will need to use a screwdriver to remove the screws that are holding the handle in place. If you have a lever type of handle, then you will need to use a wrench to loosen the nut that is holding the handle in place.

Once you have the handle loose, you can then pull it off of the shower.

  • Use a screwdriver to remove the screws that hold the handle in place
  • Carefully pull the handle away from the shower wall
  • Disconnect the handle from the shower valve
  • Remove any remaining screws or bolts that hold the shower handle in place
  • Pull the handle away from the shower wall and remove it from the shower

Remove shower handle no visible screws

If you’re trying to remove a shower handle and there are no visible screws, it’s likely that the handle is held on by a set screw. To remove a set screw, you’ll need to use a hex key or Allen wrench. The size of the hex key or Allen wrench you’ll need will depend on the size of the set screw.

Once you have the appropriate size hex key or Allen wrench, insert it into the hole in the center of the shower handle. Turn the hex key or Allen wrench counterclockwise until the set screw is loose. Once the set screw is loose, you should be able to pull the shower handle off.

how to remove a shower handle

Credit: mrplumberindy.com

How do you take out a shower handle?

Assuming you need to replace a shower handle, and not just remove it for cleaning: 1. Begin by turning off the water to the shower at the main shutoff valve. 2. Remove the handle by unscrewing the retaining screw or clip, depending on the type of handle.

3. With the handle removed, use a wrench to remove the shower valve stem by unscrewing it counterclockwise. 4. Wrap the threads of the shower valve with Teflon tape before screwing on the new shower valve stem. 5. Reattach the new shower handle, making sure the handle is in the same position as the old one.

6. Turn the water back on at the main shutoff valve and test the new handle to make sure it works properly.

How do you remove an old shower lever?

Assuming you would like tips on how to remove an old shower lever: If the shower lever is simply old and needs to be replaced, the process is relatively simple. Begin by shutting off the water to the shower, typically done by turning a knob behind the shower wall.

Next, remove the handle by unscrewing it from the shower wall. Be sure to have a towel or bucket handy to catch any water that may drip out. Finally, attach the new handle to the shower wall and turn the water back on.

If the shower lever is old and corroded, the process is a bit more difficult. First, attempt to remove the handle by unscrewing it. If the handle is stuck, apply WD-40 or another lubricant to the area and let it sit for a few minutes.

Next, use a hammer and screwdriver to lightly tap around the circumference of the handle. Be sure not to hit the handle too hard, as this could damage the shower wall. Finally, unscrew the handle and replace it with a new one.

How do you remove a single lever shower handle?

Assuming you want to remove a Moen single lever shower handle: To remove a Moen single lever shower handle, start by removing the set screw that holds the handle in place. Once the set screw is removed, the handle can be pulled off.

If the handle is stuck, try using a handle puller or a pair of pliers to wiggle it loose. Once the handle is off, you’ll be able to access the valve stem. To remove the valve stem, start by unscrewing the retaining nut that holds it in place.

Once the retaining nut is removed, the valve stem can be pulled out.

How do you remove a metal shower handle?

If you need to remove a metal shower handle, there are a few things you’ll need to do. First, you’ll need to turn off the water to the shower. Next, you’ll need to remove the escutcheon plate, which is the plate that covers the hole where the handle goes.

To do this, you’ll need to remove the screws that hold it in place. Once the escutcheon plate is removed, you should be able to see the set screw that holds the handle in place. Use a screwdriver to remove this screw, and then the handle should come right off.

Fix leaky shower head with a stuck handle

Conclusion

First, you will need to gather a few supplies including a screwdriver, adjustable wrench, and a pair of pliers. Next, locate the screw that is holding the handle in place and remove it. Once the screw is removed, the handle should come right off.

If it is stuck, you may need to use the pliers to remove it. Finally, once the handle is off, you can clean the area and replace the handle if necessary.

You can easily find the best products according to consumer reviews and ratings. Our AI technology finds the best product and describes it according to customer reviews. Not all information on this blog is 100 percent accurate.