NestAssociate is reader-supported. When you buy via the links on our site, we may earn an affiliate commission at no cost to you.

How To Replace A Moen Single Handle Bathroom Faucet Cartridge

Assuming you have a Moen single handle bathroom faucet that uses a 1200 or 1225 cartridge, here are the steps to replace it. You may need a few tools, including a 1/8″ allen wrench, a Phillips screwdriver, and pliers. First, remove the handle.

There is a set screw located under the decorative cap that needs to be removed. Once the set screw is removed, the handle will pull off. Be careful not to lose the spring and button that are under the handle.

Next, use the allen wrench to remove the retaining clip that is holding the cartridge in place. Once the retaining clip is removed, the cartridge can be pulled out. Now, take the new cartridge and lubricate the o-rings with a light layer of petroleum jelly.

Insert the new cartridge into the faucet body and hand-tighten the retaining clip. Be careful not to overtighten the clip, or it may break. Finally, replace the handle.

Line up the spring and button, and push the handle onto the stem. Screw on the set screw and tighten with the allen wrench. Replace the decorative cap, and you’re done!

  • Remove the handle from the faucet by unscrewing the setscrew in the center of the handle and pulling the handle off
  • Use a wrench to remove the retaining nut from the top of the cartridge
  • Pull the old cartridge out of the faucet and discard it
  • Insert the new cartridge into the faucet, making sure that it is properly seated
  • Replace the retaining nut and tighten it with a wrench
  • Replace the handle on the faucet and tighten the setscrew

Moen single handle bathroom faucet removal

Moen is one of the leading manufacturers of bathroom fixtures, and their single handle faucets are some of the most popular on the market. If you’re looking to remove one of these faucets, the process is actually quite simple. With a few basic tools, you’ll be able to have the old faucet out and a new one installed in no time.

To start, you’ll need to turn off the water supply to the faucet. There will be a shut-off valve located under the sink, so simply turn it to the “off” position. Once the water is off, you can go ahead and remove the handle.

There will be a small set screw located on the underside of the handle. Use a Phillips head screwdriver to remove this screw, and then the handle should come right off. Underneath the handle, you’ll see the cartridge.

This is what controls the flow of water, and it’s held in place by a retaining nut. Use a wrench to loosen and remove this nut, and then you can pull the cartridge out. Now, it’s time to install the new cartridge.

Moen makes a variety of different cartridges, so be sure to choose the one that’s compatible with your faucet. Once you have the new cartridge in place, simply reverse the steps to reassemble the faucet.

how to replace a moen single handle bathroom faucet cartridge

Credit: www.amazon.com

How do you remove the cartridge from a Moen single handle bathroom faucet?

If your Moen single handle bathroom faucet is leaking, you may need to replace the cartridge. To do this, you will need to remove the cartridge from the faucet. First, turn off the water supply to the faucet.

Next, use a wrench to remove the handle. Be careful not to damage the finish on the handle. Once the handle is removed, you will be able to see the cartridge.

Use a pair of pliers to remove the retaining clip that holds the cartridge in place. Pull the cartridge out of the faucet body. You may need to use a little force to get it out.

Now, you can install the new cartridge. Start by lubricating the O-rings on the new cartridge with a little plumber’s grease. Insert the new cartridge into the faucet body and hand-tighten the retaining clip.

Be careful not to over-tighten the clip, or you may damage the cartridge. Re-install the handle and turn on the water supply. Test the faucet to make sure it is working properly.

How do I change the cartridge on my Moen single handle faucet?

If you have a Moen single handle faucet, you may need to change the cartridge at some point. This is a relatively easy process, and you should be able to do it yourself without having to call a plumber. First, you will need to turn off the water to your faucet.

You can do this by turning the knob on the shut-off valve under your sink. Once the water is off, you can remove the handle by unscrewing the set screw that is located under the cap. Once the handle is off, you will be able to see the cartridge.

To remove the old cartridge, you will need to use a special tool that Moen sells. Once you have the tool, you can simply unscrew the old cartridge and replace it with a new one. Once the new cartridge is in place, you can screw the handle back on and turn the water back on.

You may need to bleed the line of any air that may be trapped, but other than that, your faucet should be good as new!

How do you remove a single handle bathroom faucet cartridge?

Assuming you have a single handle bathroom faucet with a removable cartridge, the process for removing it is as follows: 1. First, turn off the water supply to the faucet. This is usually done by shutting off the valves under the sink.

2. Next, open the faucet to release any water pressure that may be in the lines. 3. Use a wrench or pliers to remove the retaining nut that holds the cartridge in place. 4. With the retaining nut removed, you should be able to pull the cartridge out of the faucet.

5. Inspect the cartridge for any debris or damage. If it looks damaged, it will need to be replaced. 6. To install the new or replacement cartridge, simply reverse the steps above.

How do you replace a Moen 1225 single handle cartridge?

Moen 1225 single handle cartridges can be replaced easily. All you need is a replacement cartridge and a few tools. To replace the cartridge, first shut off the water supply to the faucet.

Next, use a Phillips screwdriver to remove the setscrew in the handle. After the setscrew is removed, pull the handle off the valve stem. Now, use a crescent wrench to remove the retaining nut that holds the cartridge in place.

Once the retaining nut is removed, the cartridge can be pulled out. To install the new cartridge, simply reverse the process. First, insert the new cartridge into the valve body and hand-tighten the retaining nut.

Next, reattach the handle and tighten the setscrew. Finally, turn the water supply back on and test the faucet.

Moen Bathroom Faucet Repair – Moen 1225

Conclusion

If your Moen bathroom faucet is giving you trouble, it might be time to replace the cartridge. This is a relatively easy fix that you can do yourself, and it will only take a few minutes. The first thing you need to do is turn off the water supply to your bathroom.

Then, open up the faucet to release any remaining water. Next, use a wrench to remove the retaining nut that holds the cartridge in place. Once the nut is loose, you can pull out the old cartridge and replace it with a new one.

Be sure to line up the new cartridge with the old one so that it goes in smoothly. Finally, replace the retaining nut and turn on the water supply. Test the faucet to make sure everything is working properly.

You can easily find the best products according to consumer reviews and ratings. Our AI technology finds the best product and describes it according to customer reviews. Not all information on this blog is 100 percent accurate.